Chicago electric 90 amp flux core welder8/24/2023 Do not use the power tool if the Power Switch does not turn it on or off. The correct tool will do the job better and safer at the rate for which it is designed.ġ7. Use the correct tool for your application. Holding the work by hand or against your body is unstable and may lead to loss of control.ġ6. Use clamps (not included) or other practical ways to secure and support the workpiece to a stable platform. For welding safety equipment, refer to number 7 on page 6.ġ5. Proper footing and balance enables better control of the power tool in unexpected situations.ġ4. Keep proper footing and balance at all times. A wrench or a key that is left attached to a rotating part of the power tool may result in personal injury.ġ3. Remove adjusting keys or wrenches before turning the power tool on. Be sure the Power Switch is off before plugging in.Ĭarrying power tools with your finger on the Power Switch, or plugging in power tools with the Power Switch on, invites accidents.ġ2. Loose clothes, jewelry, or long hair can catch fire.ġ1. Keep your hair, clothing, and gloves away from arc. A moment of inattention while operating power tools may result in serious personal injury.ġ0. Do not use a power tool while tired or under the influence of drugs, alcohol, or medication. Watch what you are doing, and use common sense when operating a power tool. These extension cords are rated for outdoor use, and reduce the risk of electric shock.ĩ. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”. Damaged Power Cords increase the risk of electric shock.Ĩ. Keep the Power Cord away from heat, oil, sharp edges, or moving parts. Never use the Power Cord to carry the tools or pull the Plug from an outlet. If the tools should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user.ħ. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Never remove the grounding prong or modify the plug in any way. Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Water entering a power tool will increase the risk of electric shock.Ħ. Do not expose power tools to rain or wet conditions. There is an increased risk of electric shock if your body is grounded.ĥ. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. Protect others in the work area from debris such as chips and sparks. Keep bystanders, children, and visitors away while operating a power tool.ĭistractions can cause you to lose control. Power tools create sparks which may ignite the dust or fumes.ģ. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Cluttered benches and dark areas invite accidents.Ģ. READ AND UNDERSTAND ALL INSTRUCTIONS.Failure to follow all instructions listed below may result in electric shock, fire, and/or serious injury.ġ. Keep the manual and invoice in a safe and dry place for future reference. Write the invoice number on the inside of the front cover. You will need the manual for the safety warnings and precautions, assembly instructions, operating and maintenance procedures, parts list and diagram. (0.9 mm tips, to account for thermal expansion of the wire)ġ4-1/2 (L) x 8-1/2 (W) x 15-1/2 (H) inches Included tips will accept 0.030 ” flux core wire Should be connected to a 20 amp minimum dedicated circuit (See explanation of Duty Cycle on page 15.) Nozzle Inspection, Cleaning, and Replacement.Ĭontact Tip Inspection, Cleaning, and Replacement. Operation.īefore You Start Welding.ĭuty Cycle (Duration of Use). Installing the Wire Reel.Ĭhanging Wire feed roller.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |